Parts Town shares tips for dealing with faulty ice machines


Parts Town has taken to its blog to share some tips for what to do when a Manitowoc ice machine stops working. 

The spare parts supplier said that while it’s not a common occurrence, a couple of issues can pop up occasionally when the unit runs on a daily basis.

To help operators who might find themselves in this situation it provided a troubleshooting guide.

Story continues below

It provided advice for various scenarios, including when the ice machine is not operating at all, when it is not releasing ice and when the ice quality is poor.

The advice in full can be seen below:

Ice Machine Doesn’t Operate
  • No power – It’s the one question everyone sighs after hearing: “is the unit plugged in?” Just check. You might be pleasantly surprised that your problem has an easy, cost-free solution.
  • Tripped circuit breaker or blown fuse – Is the breaker tripped or a fuse blown? Check your box for these problems.
  • Toggle switch isn’t on – If the ON/OFF/WASH switch isn’t set properly, or is somehow stuck between those options, your machine won’t operate. Make sure the switch is set to ON.
  • Damper is open – If the damper is held open in the down position, the machine will shut off until ice or any foreign obstructions are cleared. The damper must be upright and capable of swinging freely.
Ice Machine Stops, Restarts When Switched Off and On Again
  • Safety limit is triggered – The safety limit on some Manitowoc units is designed to stop the ice machine if there is a possibility of major component failure. Switch the machine off and back on again. If the ice machine continues to run, the condition has corrected itself and you’re good to go. If the machine stops again, an authorized service technician will need to repair the issue.

Ice Machine Not Releasing Ice or Slow to Harvest

  • Dirty machine – A dirty machine can slow down the harvest cycle or impede ice from releasing. Clean and sanitize the ice machine following the instructions in the owner’s manual.
  • Machine isn’t level – Is the ice machine level? Your unit must sit flat on the floor for optimal performance.
  • Ambient temperature is too warm – On air-cooled models, the air temperature must be at least 40 degrees Fahrenheit or 4 degrees Celsius. Make sure the room isn’t too hot.
  • Water regulating valve leaking – On water-cooled models, if the water regulating valve is leaking in harvest mode, it could cause a problem. Replace the valve.
Ice Machine Doesn’t Cycle Into Harvest Mode
  • Timer hasn’t stopped – The harvest sequence cannot be initiated until a 6-minute freeze timer has elapsed. If ice forms before then, it will be held until the timer completes.
  • Ice thickness probe is dirty or disconnected – Clean the probe if it’s dirty. If the ice thickness probe need adjustment, make sure it’s adjusted so the water flow, not the ice, contacts the probe to initiate a harvest.
  • Uneven ice fill – If the ice is thin at the top of the evaporator, continue reading for the solution further down in this post under the problem “shallow or incomplete cubes.”

Ice Quality is Poor, Soft or Not Clear

  • Poor water quality – If your water quality is poor, there are many potentially expensive problems that can occur. Contact a qualified service company to test water quality and for the right filter recommendations.
  • Water filters are broken or dirty – If you already have a filtration system, your water filter may need replacing.
  • Dirty machine – Lime scale can cause poor ice quality. Follow the manufacturer’s instruction to clean and sanitize your machine.

Shallow/Incomplete Ice Cubes or Ice Fill Pattern Incomplete on Evaporator

  • Ice thickness probe out of adjustment – See if the ice thickness probe need adjustment.
  • Water level is too high or low – Make sure the water trough level isn’t too high or too low.
  • Water temperature is too high – Ice machines require a cold water supply. Make sure there is not a hot water supply line into the machine.
  • Water filter is broken – The water filter might be too dirty or damaged. You’ll need to replace it.
  • Water pressure is too low – The water pressure into the machine must be 20-80 psi (137.9-551.5 kPA).
  • Water float valve – See if the water float valve and its filter screen are dirty. Either can cause shallow or incomplete ice cubes.
  • Machine isn’t level – Make sure the machine is level. The machine must sit flat on the floor for optimal performance.

Low Ice Capacity

  • Disconnected water supply – Is the water supply connected? Make sure the water service valve is open.
  • Water float valve – See if the water float valve and its filter screen are dirty. Either can cause low ice capacity.
  • Condenser is dirty – Make sure the condenser is clean and free of obstructions, especially in air-cooled models.
  • Air temperature is too high – The air temperature must not exceed 110 degrees Fahrenheit (43 degrees Celsius) in air-cooled models.

Not finding the answer to your troubleshooting question? Check out our collection of Manitowoc Ice machine manuals to assist you, or contact an authorized service technician to diagnose and resolve any issue.

Tags : ice machinesManitowocParts Town
Patrick Cremona

The author Patrick Cremona

Leave a Response

Thank you! Your subscription has been confirmed. You'll hear from us soon.
Enter your email to join the thousands of other professionals receiving breaking news from Catering Insight